Workspace

Published Work

This page lists Dr. Stringer's publications from the past five years.  A complete list of publications can be found in his his CV, lined at the bottom of the page.

 

2020

  • Edmonds, K. Stringer, D., Valco, M., “Experimental Results of Transient Variable Speed Rotor Performance for Small UAS Propulsion Scalability,” Vertical Flight Society 76th Annual Forum, October 6-8, 2020, Virtual.

  • Edmonds, K., and Stringer, D., “Unmanned VTOL Propulsion Research – Scalability of Quadcopter Rotor-Motor Configurations Outside the sUAS Regime,” Final Report, ARL-CR-0848, Grant No. W911NF-18-2-0024, May 2020, https://apps.dtic.mil/sti/pdfs/AD1102551.pdf.

  • Gajowski, A, Fertig, A., Stringer, D., “Unmanned eVTOL Propulsion Scalability: Thermal Characterization of UAS Motors via Experimentation,” AUVSI Xponential, Poster Session, October, 2020, Virtual.

  • Stringer, D., Edmonds, K., D., Valco, M., “A Prediction Model of Transient Variable Speed Rotor Performance for Small UAS Propulsion Scalability,” Vertical Flight Society 76th Annual Forum, October 6-8, 2020, Virtual.

2019

  • Bihn, S., Fertig, A., Stringer, D., “Improving Vertical Axis Wind Turbine Feasibility: Predicting Turbine Airfoil Performance Via Wind Tunnel Experimentation,” Environmental Science & Design Research Symposium, Poster Session, Kent State University, March 20-21 2019.

  • Edmonds, K. Stringer, D., “Unmanned VTOL Propulsion Research – Scalability of Quadcopter Rotor-Motor Configurations Outside the sUAS Regime,” AUVSI Xponential, April 29 – May 2, 2019, Chicago, Illinois.

2018

  • Stringer, D., Bunner, D., and Winkler, R., “Aerospace Capstone Design: Interactive Sizing Estimates for Increasing Designer Intuition and Mitigating Risk in the Early Stages of Aircraft Conceptual Design,” Proceedings of the 2018 American Society for Engineering Education Annual Conference and Exposition, Salt Lake City, Utah, June 24-27, 2018.

  • Davis, T., Stringer, D., and McFarland, M., “Integrating Veteran Experiences into Engineering Design: Veteran-Led Student Development of High-Power Rocket Competition Team,” Proceedings of the 2018 American Society for Engineering Education Annual Conference and Exposition, Salt Lake City, Utah, June 24-27, 2018.

  • Abdul-Aziz, A., Bissler, R., and Stringer, D., “Turbofan Engine Performance Study Under Simulated Failure and Nontraditional Flight Conditions,” Proceedings of the SPIE 10601, Smart Materials and Nondestructive Evaluation for Energy Systems IV, Paper 10601-5, Denver, Colorado, March 4-8, 2018, doi: 10.1117/12.2297144.

  • Stringer, D., Hartman, P. Bunner, D., and Fisch, M.  “A New 360° Airfoil Model for Predicting Airfoil Thrust Potential in Vertical-Axis Wind Turbine Designs.”  January 2018 Journal of Renewable and Sustainable Energy 10(1), 13304, doi: 10.1063/1.5011207.

2017

  • Stringer, D., and McFarland, M.  “Combining Engineering and Engineering Technology Programs into a Single Design Sequence.”  Fall/Winter 2017 Technology Interface International Journal 18(1), 5-13.

2016

  • Stringer, D., McFarland, M., “Combining Engineering and Engineering Technology Programs into a Single Capstone Design Sequence,” Proceedings of the 2016 IAJC/ISAM International Conference, Orlando, Florida, November 6-8, 2016.  This is the same as the journal article listed above.

  • Stringer, D., and McFarland, M., “Veterans’ Contributions to Enhancing the Capstone Learning Experience of Engineering Cohorts,” Proceedings of the 2016 American Society for Engineering Education Annual Conference and Exposition, New Orleans, Louisiana, June 26-29, 2016.